108 Glow in the Dark
Item is on a Pre-order Basis as some of our items may not be available to your preferred branch.
To avoid the inconvenience, kindly send us a message through our Chat Button for item availability.
- 108 Glow-in-the-Dark (phosphorescent) is a plastisol screen printing ink that a bright, greenish glow when exposed to light and viewed in a darken area.
- 108 Glow-in-the-Dark can be used for direct print or cold peel transfer applications.
- 108 Glow-in-the-Dark is ready for use straight from the container.
Direct Prints: 108 Glow-in-the-Dark ink should be used right from the container without any modifications. If thinning is required, use 1% to 5% by volume of 1110 Curable Reducer. Adding too much reducer or other additives will diminish opacity and glow.
Transfers (cold peel): It is important that the inks are only partially gelled, otherwise the inks will not have adequate adhesion during the final transfer application.
- 108 Glow-in-the-Dark is not a low bleed ink. Always test print the fabric to be printed before beginning production. It is best to do some long term testing on fabrics to determine if they are going to bleed. Bleeding or dye migration may not occur right away
- 108 Glow-in-the-Dark is a very transparent ink and works best when printed on white fabric or over a white base.
- Do not fuse or cure the ink at too high a temperature (over 330°F or 166°C) as the phosphorescent pigment used in the ink can be damaged and not glow properly.
- Adding too much reducer, soft hand additive or clear base will diminish glow. STIR the ink prior to printing on press and after addition of reducers or additives.
- Heavier ink deposits of 108 Glow-in-the-Dark will result in increased phosphorescence (glow brightness) and a longer glow after exposure to a bright light source. Depending on the amount of light exposure to the ink, the darkness of the of the area where the ink is being viewed and the eye sensitivity of the person viewing the ink, the glow may be visible anywhere from 15 minutes up to two hours.
- When making cold peel transfers for dark fabrics, back transfers with white ink. Cold peel transfers should be applied at 350°F to 375°F (177°C to 191°C), medium pressure (40 lbs.) for 10 to 15 seconds.
- Test dryer temperatures and wash test printed product before and during a production run.
- 100% Cotton
- Some Cotton/Polyester Blends
- 108 Glow-in-the-Dark should be used right from the container without any modifications
- If modification is necessary, use 1% to 5% by volume of 1110 Curable Reducer
- 60-230 t/in (24-90 t/cm) mono filament
- Any direct or indirect emulsion or capillary film in the 35 to 70 micron range
- 65-75 Durometer Sharp edge
- 325ºF(163ºC) for 1 minute dependent on dryer speed and temperature settings
- Any eco-friendly plastisol screen wash
- Quart, 1 gallon, 5 gallon, 30 gallon or 50 gallon containers
STORAGE OF INK CONTAINERS
- 65º to 90ºF (18ºC to 32ºC). Avoid storage in direct sunlight. Keep containers well sealed
- Refer to SDS prior to use
|Dimensions||3.1 × 0.1 × 1.5 cm|
BUS TERMINAL TO TERMINAL
Victory Liner | Superlines | Partas | Genesis | Florida | Philtranco | Baliwag Transit | Jam Liner | Jac Liner | DLTBCo | Dagupan Bus | Elavil Bus | Five Star | Isarog | Joy Bus | Ohayami Trans | Penafrancia | Raymond Bus | RORO Bus | RSL Bus | Silver Star | Solid North | Viron
CARGO FORWARDER |COURIER | TRUCKING
Pambato | CaPEx | AP Cargo | LBC | Air21 | Jrs Express | Xend | A Best Express | DHL | Ezgo Truck
Same day shipping if payment is made within our cut off time 2pm
Please contact our Costumer Representative to verify the same day delivery and availability of the item.
Costumer Representative Hotline: +63917 8273584 | +632 6240284.